View NSVS822_76742.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NSVS822 Dec-01
JRC SAW FILTER
NSVS822
Application
AMPS RX
Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1. Table 1. Electrical Specifications Item Spec. Typical Input and Output Impedance 50 Nominal Center Frequency (f0) 881.5MHz Insertion Loss 869~894MHz 2.6dB max. 2.0dB Response Variation 869~894MHz 1.5dB max. 0.6dB Input and Output VSWR 869~894MHz 2.5 max. 2.1 Out of Band Rejection DC~800MHz 20dB min. 23dB (Relative to 824~849MHz 32dB min. 36dB Through Level) 1000~3000MHz 20dB min. 24dB (Operating Temperature Range: -30~+85C)
Maximum Rating: (Table 2) Table 2. Maximum Ratings Item Maximum Input Power Maximum DC Voltage Operating Temperature Range Storage Temperature Rating +20dBm 7.5V -30~+85C -40~+95C
Mechanical Specifications: (Fig.2) Package is designed as small as 2.5x2.0x1.0[mm3] for SMD (Surface Mount Device) type. Notice: This part is electrostatic discharge sensitive and may be damaged by improper handling.
Communications Equipment Division Communications Equipment Marketing Department
17-22 Akasaka 2-chome minato-ku, Tokyo. 107-0052 Japan Tel. +81 3-3584-8811 Fax. +81 3-3584-8876 http://www.jrc.co.jp/product/comm/deveice/saw/saw_top.html (Japanese) http://www.jrc.co.jp/product/comm/device/saw/saw_top_e.html (English)
NSVS822 Dec-01
OUT 50 IN 50
1 SAW 2 3 4
Fig.1 Measuring circuit
2.50.1 (2)
Q9
(1)
2 .0 0 .1
Marking (1) Part Number Mark (2) Lot Number (Month) *Oct.--- X Nov.--- Y Dec.--- Z (3) Part number Mark
1 .0 0 .1
2
3
Pin no. 1 2 3 4
(0 .6 3 ) [4x]
Connection GND IN/OUT GND OUT/IN
1
(0.75) [4x]
Fig.2 Package dimensions (in mm)
3.3 1.15 1.15
2.8
1.03
1.03
Fig.3 Desirable land area (in mm)
(0 .2) [2x]
4
NSVS822 Dec-01
Notice
1. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -30C or more than +85C, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. 2. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350C max., the time of soldering: 10 seconds max., the power of soldering iron: 30W max.. 3. Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. 4. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. 5. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. 6. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. 7. As it might be a cause of degradation or destruction to apply D.C. voltage between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note 1. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products.
AMPS Rx SAW FILTER NSVS822
0 S21
FREQUENCY CHARACTERISTICS
0
Insertion Loss [dB]
10
2
20
4
30
6
40
8
50 CH1 : center 881.5 span 200 CH2 : center 881.5 span 200
10
S11
S22
S11
11 9 11 9
S22
VSWR
7 5 3 1 781.5 Frequency [MHz]
VSWR
7 5 3 1 781.5 Frequency [MHz]
981.5
981.5
0
S21
InsertionLoss [dB]
10 20 30 40 50 3 Frequency [MHz] 6000
Japan Radio Co.,Ltd.
Insertion Loss [dB]

▲Up To Search▲

Price & Availability of NSVS822

	To Download NSVS822 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .